Truss Bridge

A truss bridge is a bridge whose load-bearing superstructure is composed of a truss, a structure of connected elements, usually forming triangular units. The connected elements (typically straight) may be stressed from tension, compression, or sometimes both in response to dynamic loads. The basic types of truss bridges shown in this article have simple designs which could be easily analyzed by 19th and early 20th-century engineers. A truss bridge is economical to construct because it uses materials efficiently.

Design

The nature of a truss allows the analysis of its structure using a few assumptions and the application of Newton's laws of motion according to the branch of physics known as statics. For purposes of analysis, trusses are assumed to be pin jointed where the straight components meet, meaning that taken alone, every joint on the structure is functionally considered to be a flexible joint as opposed to a rigid joint with strength to maintain its own shape, and the resulting shape and strength of the structure is only maintained by the interlocking of the components. This assumption means that members of the truss (chords, verticals and diagonals) will act only in tension or compression. A more complex analysis is required where rigid joints impose significant bending loads upon the elements, as in a Vierendeel truss.

In the bridge illustrated in the infobox at the top, vertical members are in tension, lower horizontal members in tension, shear, and bending, outer diagonal and top members are in compression, while the inner diagonals are in tension. The central vertical member stabilizes the upper compression member, preventing it from buckling. If the top member is sufficiently stiff then this vertical element may be eliminated. If the lower chord (a horizontal member of a truss) is sufficiently resistant to bending and shear, the outer vertical elements may be eliminated, but with additional strength added to other members in compensation. The ability to distribute the forces in various ways has led to a large variety of truss bridge types. Some types may be more advantageous when wood is employed for compression elements while other types may be easier to erect in particular site conditions, or when the balance between labor, machinery and material costs have certain favorable proportions.

The inclusion of the elements shown is largely an engineering decision based upon economics, being a balance between the costs of raw materials, off-site fabrication, component transportation, on-site erection, the availability of machinery and the cost of labor. In other cases the appearance of the structure may take on greater importance and so influence the design decisions beyond mere matters of economics. Modern materials such as prestressed concrete and fabrication methods, such as automated welding, and the changing price of steel relative to that of labor have significantly influenced the design of modern bridges.

Model bridges

A pure truss can be represented as a pin-jointed structure, one where the only forces on the truss members are tension or compression, not bending. This is used in the teaching of statics, by the building of model bridges from spaghetti. Spaghetti is brittle and although it can carry a modest tension force, it breaks easily if bent. A model spaghetti bridge thus demonstrates the use of a truss structure to produce a usefully strong complete structure from individually weak elements.

History in the United States

Because wood was in abundance, early truss bridges would typically use carefully fitted timbers for members taking compression and iron rods for tension members, usually constructed as a covered bridge to protect the structure. In 1820 a simple form of truss, Town's lattice truss, was patented, and had the advantage of requiring neither high labor skills nor much metal. Few iron truss bridges were built in the United States before 1850.

Truss bridges became a common type of bridge built from the 1870s through the 1930s. Examples of these bridges still remain across the US, but their numbers are dropping rapidly as they are demolished and replaced with new structures. As metal slowly started to replace timber, wrought iron bridges in the US started being built on a large scale in the 1870s. Bowstring truss bridges were a common truss design during this time, with their arched top chords. Companies like the Massillon Bridge Company of Massillon, Ohio, and the King Bridge Company of Cleveland, Ohio, became well-known, as they marketed their designs to cities and townships. The bowstring truss design fell out of favor due to a lack of durability, and gave way to the Pratt truss design, which was stronger. Again, the bridge companies marketed their designs, with the Wrought Iron Bridge Company in the lead. As the 1880s and 1890s progressed, steel began to replace wrought iron as the preferred material. Other truss designs were used during this time, including the camel-back. By the 1910s, many states developed standard plan truss bridges, including steel Warren pony truss bridges. As the 1920s and 1930s progressed, some states, such as Pennsylvania, continued to build steel truss bridges, including massive steel through-truss bridges for long spans. Other states, such as Michigan, used standard plan concrete girder and beam bridges, and only a limited number of truss bridges were built.

Roadbed types

The truss may carry its roadbed on top, in the middle, or at the bottom of the truss. Bridges with the roadbed at the top or the bottom are the most common as this allows both the top and bottom to be stiffened, forming a box truss. When the roadbed is atop the truss it is called a deck truss (an example of this was the I-35W Mississippi River bridge). When the truss members are both above and below the roadbed it is called a through truss (an example of this application is the Pulaski Skyway), and where the sides extend above the roadbed but are not connected, a pony truss or half-through truss.

Sometimes both the upper and lower chords support roadbeds, forming a double-decked truss. This can be used to separate rail from road traffic or to separate the two directions of road traffic.

Since through truss bridges have supports located over the bridge deck, they are susceptible to being hit by overheight loads when used on highways. The I-5 Skagit River bridge collapsed after such a strike; before the collapse, similar incidents had been common and had necessitated frequent repairs.

Gallery

Image:LittleManateeRiver.jpg, Pratt through truss of the former Seaboard Air Line Railway, located near the village of Willow, Florida; abandoned since the mid-1980s
Image:ErieCanalRRBridge04 1A.jpg, Deck truss railroad bridge over the Erie Canal in Lockport, New York
Image:General Hertzog Bridge over Orange River at Aliwal North.jpg, The four span through truss General Hertzog Bridge over the Orange River at Aliwal North carries vehicular traffic
File:05-23-13 Skagit Bridge Collapse.jpg, The through truss Skagit River bridge on Interstate 5 collapsed after an overhead support was hit by a passing truck
File:Old San Jacinto River Truss Bridge -- Humble, Texas.jpg, Old San Jacinto River truss bridge – Humble, Texas
Image:Puente Tacuarembó 02.jpg, Pony truss bridge of reinforced concrete
Image:Sky gate bridge01s3200.jpg, Sky Gate Bridge R at Kansai International Airport, Osaka, Japan, is the longest double-decked truss bridge in the world. It carries three lanes of automobile traffic on top and two of rail below over nine truss spans.
File:Railroad Truss bridge over trinity river near Goodrich, Texas.jpg, Railroad Truss bridge over Trinity River near Goodrich, Texas
Image:HartBridgeJax.jpg, The Hart Bridge spanning the St. Johns River in Jacksonville, Florida, is a continuous, cantilevered truss bridge which combines a suspended road deck on the main span and through truss decks on the adjacent approach spans
File:Columbus and Greenville Railway bridge over Yazoo River.jpg, A railway bridge with a rail track in Leflore County, Mississippi
File:Chevelon Creek Bridge.jpg, Chevelon Creek Warren Pony Truss Bridge,Chevelon Creek, Navajo County Arizona built 1913
File:Željeznički most, Mursko Središće.3.jpg, Side view of the iron truss railway bridge over Mura River in Mursko Središće, Croatia
File:Railroad Truss Drawbridge across Buffalo Bayou -- Houston.jpg, Railroad Truss Drawbridge across Buffalo Bayou—Houston

Multiple spans

Truss bridges consisting of more than one span may be either a continuous truss or a series of simple trusses. In the simple truss design, each span is supported only at the ends and is fully independent of any adjacent spans. Each span must fully support the weight of any vehicles traveling over it (the live load).

In contrast, a continuous truss functions as a single rigid structure over multiple supports. This means that the live load on one span is partially supported by the other spans, and consequently it is possible to use less material in the truss. Continuous truss bridges were not very common before the mid-20th century because they are statically indeterminate, which makes them difficult to design without the use of computers.

A multi-span truss bridge may also be constructed using cantilever spans, which are supported at only one end rather than both ends like other types of trusses. Unlike a continuous truss, a cantilever truss does not need to be connected rigidly, or indeed at all, at the center. Many cantilever bridges, like the Quebec Bridge shown below, have two cantilever spans supporting a simple truss in the center. The bridge would remain standing if the simple truss section were removed.

File:Bally Bridge.jpg, A multi-span simple truss bridge, Vivekananda Setu over the Hooghly River in Kolkata, India.
File:Kingston-Rhinecliff Bridge2.JPG, A continuous truss bridge, Kingston–Rhinecliff Bridge over the Hudson River in New York, United States.
File:Le pont de Québec, de l'embouchure de la rivière Chaudière.jpg, A cantilever truss bridge, Quebec Bridge over the Saint Lawrence River in Quebec, Canada.

Truss types used in bridges

Bridges are the most widely known examples of truss use. There are many types, some of them dating back hundreds of years. Below are some of the more common designs.

Allan truss

The Allan truss, designed by Percy Allan, is partly based on the Howe truss. The first Allan truss was completed on 13 August 1894 over Glennies Creek at Camberwell, New South Wales and the last Allan truss bridge was built over Mill Creek near Wisemans Ferry in 1929. Completed in March 1895, the Tharwa Bridge located at Tharwa, Australian Capital Territory, was the second Allan truss bridge to be built, the oldest surviving bridge in the Australian Capital Territory and the oldest, longest continuously used Allan truss bridge. Completed in November 1895, the Hampden Bridge in Wagga Wagga, New South Wales, Australia, the first of the Allan truss bridges with overhead bracing, was originally designed as a steel bridge but was constructed with timber to reduce cost. In his design, Allan used Australian ironbark for its strength. A similar bridge also designed by Percy Allen is the Victoria Bridge on Prince Street, Picton, New South Wales. Also constructed of ironbark, the bridge is still in use today for pedestrian and light traffic.

Bailey truss

The Bailey truss was designed by the British in 1940-1941 for military uses during World War II. A short selection of prefabricated modular components could be easily and speedily combined on land in various configurations to adapt to the needs at the site and allow rapid deployment of completed trusses. In the image, note the use of pairs of doubled trusses to adapt to the span and load requirements. In other applications the trusses may be stacked vertically, and doubled as necessary.

Baltimore truss

The Baltimore truss is a subclass of the Pratt truss. A Baltimore truss has additional bracing in the lower section of the truss to prevent buckling in the compression members and to control deflection. It is mainly used for rail bridges, showing off a simple and very strong design. In the Pratt truss the intersection of the verticals and the lower horizontal tension members are used to anchor the supports for the short-span girders under the tracks (among other things). With the Baltimore truss, there are almost twice as many points for this to happen because the short verticals will also be used to anchor the supports. Thus the short-span girders can be made lighter because their span is shorter. A good example of the Baltimore truss is the Amtrak Old Saybrook – Old Lyme Bridge in Connecticut, United States.

Bollman truss

The Bollman Truss Railroad Bridge at Savage, Maryland, United States is the only surviving example of a revolutionary design in the history of American bridge engineering. The type was named for its inventor, Wendel Bollman, a self-educated Baltimore engineer. It was the first successful all-metal bridge design (patented in 1852) to be adopted and consistently used on a railroad. The design employs wrought iron tension members and cast iron compression members. The use of multiple independent tension elements reduces the likelihood of catastrophic failure. The structure was also easy to assemble.

The Wells Creek Bollman Bridge is the only other bridge designed by Wendel Bollman still in existence, but it is a Warren truss configuration.

Bowstring truss

The bowstring truss bridge was patented in 1841 by Squire Whipple. While similar in appearance to a tied-arch bridge, a bowstring truss has diagonal load-bearing members: these diagonals result in a structure that more closely matches a Parker truss or Pratt truss than a true arch.

Brown truss

In the Brown truss all vertical elements are under tension, with exception of the end posts. This type of truss is particularly suited for timber structures that use iron rods as tension members.

Brunel truss

See Lenticular truss below.

Burr arch truss

This combines an arch with a truss to form a structure both strong and rigid.

Cantilever truss

Most trusses have the lower chord under tension and the upper chord under compression. In a cantilever truss the situation is reversed, at least over a portion of the span. The typical cantilever truss bridge is a "balanced cantilever", which enables the construction to proceed outward from a central vertical spar in each direction. Usually these are built in pairs until the outer sections may be anchored to footings. A central gap, if present, can then be filled by lifting a conventional truss into place or by building it in place using a "traveling support". In another method of construction, one outboard half of each balanced truss is built upon temporary falsework. When the outboard halves are completed and anchored the inboard halves may then be constructed and the center section completed as described above.

Fink truss

The Fink truss was designed by Albert Fink of Germany in 1854. This type of bridge was popular with the Baltimore and Ohio Railroad. The Appomattox High Bridge on the Norfolk and Western Railway included 21 Fink deck truss spans from 1869 until their replacement in 1886.

There are also inverted Fink truss bridges such as the Moody Pedestrian Bridge in Austin, Texas.

Howe truss

The Howe truss, patented in 1840 by Massachusetts millwright William Howe, includes vertical members and diagonals that slope up towards the center, the opposite of the Pratt truss.Matsuo Bridge Company
Bridge Types – Truss
, accessed September 2007
In contrast to the Pratt truss, the diagonal web members are in compression and the vertical web members are in tension. Few of these bridges remain standing. Examples include Jay Bridge in Jay, New York; McConnell's Mill Covered Bridge; Sandy Creek Covered Bridge in Jefferson County, Missouri; and Westham Island Bridge in Delta, British Columbia, Canada.

Image:Large Timber Howe Truss.jpg, A large timber Howe truss in a commercial building.
Image:Jay Bridge interior.jpg, Jay Bridge showing the truss design.
Image:Westham island bridge.jpg, Westham Island Bridge showing its wooden truss design.

K-truss

The K-truss is named after the ''K'' formed in each panel by the vertical member and two oblique members. Examples are the Südbrücke rail bridge over the River Rhine, Mainz, Germany, the bridge on I-895 (Baltimore Harbor Tunnel Thruway) in Baltimore, Maryland, the Long–Allen Bridge in Morgan City, Louisiana (Morgan City Bridge) with three 600-foot-long spans, and the Wax Lake Outlet bridge in Calumet, Louisiana

Kingpost truss

One of the simplest truss styles to implement, the king post consists of two angled supports leaning into a common vertical support.

Lattice truss (Town's lattice truss)

This type of bridge uses a substantial number of lightweight elements, easing the task of construction. Truss elements are usually of wood, iron, or steel.

Lenticular truss

A lenticular truss bridge includes a lens-shape truss, with trusses between an upper chord (functioning as an arch) that curves up and then down to end points, and a lower chord (functioning as a suspension cable) that curves down and then up to meet at the same end points. Where the arches extend above and below the roadbed, it is called a lenticular pony truss bridge. The Pauli truss bridge is a specific variant of the lenticular truss, but the terms are not interchangeable.

One type of lenticular truss consists of arcuate upper compression chords and lower eyebar chain tension links. Brunel's Royal Albert Bridge over the River Tamar between Devon and Cornwall uses a single tubular upper chord. As the horizontal tension and compression forces are balanced these horizontal forces are not transferred to the supporting pylons (as is the case with most arch types). This in turn enables the truss to be fabricated on the ground and then to be raised by jacking as supporting masonry pylons are constructed. This truss has been used in the construction of a stadium, with the upper chords of parallel trusses supporting a roof that may be rolled back. The Smithfield Street Bridge in Pittsburgh, Pennsylvania, is another example of this type.

An example of a lenticular pony truss bridge that uses regular spans of iron is the Turn-of-River Bridge designed and manufactured by the Berlin Iron Bridge Co.

The Pauli truss is a variant of the lenticular truss, "with the top chord carefully shaped so that it has a constant force along the entire length of the truss." It is named after , whose 1857 railway bridge (the ) spanned the Isar near Munich. (''See also Grosshesselohe Isartal station''.) The term Pauli truss is not interchangeable with the term lenticular truss and, according to Thomas Boothby, the casual use of the term has clouded the literature.

Long truss

The Long truss was designed by Stephen H. Long in 1830. The design resembles a Howe truss, but is entirely made of wood instead of a combination of wood and metal. The longest surviving example is the Eldean Covered Bridge north of Troy, Ohio, spanning . One of the earliest examples is the Old Blenheim Bridge, which with a span of and a total length of long was the second-longest covered bridge in the United States, until its destruction from flooding in 2011.

The Busching bridge, often erroneously used as an example of a Long truss, is an example of a Howe truss, as the verticals are metal rods.

Parker (camelback) truss

A Parker truss bridge is a Pratt truss design with a polygonal upper chord. A "camelback" is a subset of the Parker type, where the upper chord consists of exactly five segments. An example of a Parker truss is the Traffic Bridge in Saskatoon, Canada. An example of a camelback truss is the Woolsey Bridge near Woolsey, Arkansas.

Partridge truss

Designed and patented in 1872 by Reuben Partridge, after local bridge designs proved ineffective against road traffic and heavy rains.Kennedy, Willella Shearer. "Heritage: Being Little Stories of Union County". ''Union County Historical Society'', Printed by The Marysville Journal Tribune. 1963. Pg. 48. It became the standard for covered bridges built in central Ohio in the late 1800s and early 1900s.

Pegram truss

The Pegram truss is a hybrid between the Warren and Parker trusses where the upper chords are all of equal length and the lower chords are longer than the corresponding upper chord. Because of the difference in upper and lower chord length, each panel is not square. The members which would be vertical in a Parker truss vary from near vertical in the center of the span to diagonal near each end (like a Warren truss). George H. Pegram, while the chief engineer of Edge Moor Iron Company in Wilmington, Delaware, patented this truss design in 1885.

The Pegram truss consists of a Parker type design with the vertical posts leaning towards the center at an angle between 60 and 75°. The variable post angle and constant chord length allowed steel in existing bridges to be recycled into a new span using the Pegram truss design. This design also facilitated reassembly and permitted a bridge to be adjusted to fit different span lengths. There are twelve known remaining Pegram span bridges in the United States with seven in Idaho, two in Kansas, and one each in California, Washington, and Utah.

Pennsylvania (Petit) truss

The Pennsylvania (Petit) truss is a variation on the Pratt truss. The Pratt truss includes braced diagonal members in all panels; the Pennsylvania truss adds to this design half-length struts or ties in the top, bottom, or both parts of the panels. It is named after the Pennsylvania Railroad, which pioneered this design. It was once used for hundreds of bridges in the United States, but fell out of favor in the 1930s, and very few bridges of this design remain. Examples of this truss type include the Lower Trenton Bridge in Trenton, New Jersey

HOME


Content is Copyleft
Website design, code, and AI is Copyrighted (c) 2014-2017 by Stephen Payne


Consider donating to Wikimedia



As an Amazon Associate I earn from qualifying purchases